 |
Specification - SB 10 Controller
|
|
|
|
|
|
|
|
|
|
Dimensions
|
|
|
SB Controller - 1U case 270 mm deep
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Weight
|
|
|
5.5 kgs
|
|
|
|
|
|
|
|
|
Input
|
|
|
|
|
|
|
|
|
|
Connectors
|
|
|
|
2 off XLR and 1/4 inch jack combo socket
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Impedance
|
|
|
|
10k electronically balanced
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Wiring
|
|
|
|
Pin 1 (Sleeve) ground
Pin 2 (Tip) hot
Pin 3 (Ring) cold
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Gain
|
|
|
|
-14 dBu to +6 dBu
|
|
|
|
|
|
|
|
|
|
Outputs
|
|
|
|
|
|
|
|
|
|
Left and right monitor outputs
|
|
|
|
2 off XLR3 type male left & right
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Impedance
|
|
|
|
<100 ohm electronically balanced
Wiring Pin 1 ground, Pin 2 hot, Pin 3 cold
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Sub Bass output
|
|
|
|
1 pair binding posts
|
|
|
|
|
|
|
|
|
|
Filters
|
|
|
|
|
|
|
|
|
|
Left & right input summed to sub output
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Subsonic/High pass
|
|
|
|
-3dB @ 14 Hz, 24dB/oct or -3dB @ 28 Hz, 24dB/oct (set by internal jumper)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Low Pass
|
|
|
|
-3dB @ 40 Hz to 135 Hz, externally adjustable @ 24db /oct or full range on CH A
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Left right input to left & right output
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Ultra sonic
|
|
|
|
-1dB @ 100k
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
High pass
|
|
|
|
-3dB @ 40 Hz to 135 Hz, externally adjustable @ 24db /oct or full range on CH A
|
|
|
|
|
|
|
|
|
|
Power Amplifer
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
> 210W rms continuous
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
T.H.D.
|
|
|
|
< 0.03% at levels up to 1dB below clip, 20 Hz - 120 Hz typ 0.005% @ 20W rms 100 Hz
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Hum + Noise
|
|
|
|
< -100 dB referred to clip
|
|
|
|
|
|
|
|
|
|
Controls
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Crossover Frequency 40 - 135 Hz, front panel pot
Test (Band limited pink noise), front panel recessed switch (LED indicates when on)
Sub bass bypass, front panel switch (LED indicates when bypassed)
Sub Gain -14 to +6, front panel pot (Sub level indicated with LED Meter)
Sub Phase, front panel pot
Sub Polarity, front panel recessed switch (LED indication for positive and negative polarity)
Power, front panel switch
Left channel sub filter bypass, rear mounted recessed switch
Subsonic filter 14 or 28 Hz, internal jumpers
|
|
|
|
|
|
|
|
|
|
Power requirements
|
|
|
|
|
|
|
|
|
|
Voltage
|
|
|
|
Set by internal plug: nominal 115V or 230V @ 50-60Hz AC
230V setting: Min 160V (restricted output power): Max 255V
115V setting: Min 80V (restricted output power): Max 127V
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Consumption
|
|
|
|
Quiscent: 30W. Typical use: 50W. Max: 200W.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Note 0dBu = 775mV into open circuit
|
|