 |
Specification - VS2108
|
|
|
|
|
|
|
|
|
|
Size (WxHxD)
|
|
|
337mm x 400mm x 340mm
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Weight
|
|
|
22 kgs
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Drivers
|
|
|
Bass: 200 mm (8")
HF: soft dome 28mm (1.125")
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Maximum SPL
|
|
|
112dB(C)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Frequency Response
|
|
|
48Hz - 20kHz +/-2dB
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Sensitivity
|
|
|
|
90.5dB at 1W at 1m
|
|
|
|
|
|
|
|
|
|
Input
|
|
|
|
|
|
|
|
|
|
Connector
|
|
|
|
XLR3 Female
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Impedance
|
|
|
|
10 kohm. Electronically balanced, RF filtered
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Wiring
|
|
|
|
Pin 1 Ground, Pin 2 Hot, Pin 3 Cold
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Sensitivity
|
|
|
|
Rear switch to select:
-18dBu to 0dBu in 2dB steps for 100dB SPL
Max input for clip +20dBu at 5kHz on 0dBu setting
|
|
|
|
|
|
|
|
|
|
Filters
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Subsonic
|
|
|
|
-3dB at 27Hz, 12dB/oct (LF equaliser out).
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
RF
|
|
|
|
-3dB at 25kHz, 6dB/oct (HF equaliser out).
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Crossover
|
|
|
|
1.25kHz, 24dB/oct.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
User LF EQ
|
|
|
|
3 position rear switch to select OFF for normal use (nominally flat), EXTENDED for nominal +1dB lift below 55 Hz, and OUT for use with an external sub-woofer.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
User HF EQ
|
|
|
|
3 position rear switch to select OFF for normal use (nominally flat), LIFT for nominal +1dB from 5kHz and CUT -1dB from 6kHz.
|
|
|
|
|
|
|
|
|
|
Power Amplifier
|
|
|
|
|
|
|
|
|
|
LF output power
|
|
|
|
>110W rms continuous.*
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
HF output power
|
|
|
|
>100W rms continuous.*
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
* The continuous rating is for a period not exceeding 5 minutes with unrestricted airflow (100mm clearance) around the amplifier heatsinks and ambient temperature is < 30°C.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
T.H.D.
|
|
|
|
<0.03% at levels up to 1dB below clip, 20Hz - 20kHz typ. 0.005% at 20W rms 1kHz.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Hum + Noise
|
|
|
|
>-100dB referred to clip
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Indication
|
|
|
|
|
|
|
|
|
|
Power on
|
|
|
|
Front mounted LED (green) indicates power applied
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Overload
|
|
|
|
Front mounted LED (flashes red) indicates 0.5dB below signal clip.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Thermal protection
|
|
|
|
Front mounted LED turns red, signal is muted and amplifier switches to standby mode during thermal protection cooling cycle. Normal operation resumes when heatsink temperature drops by 20°C.
|
|
|
|
|
|
|
|
|
|
Power requirements
|
|
|
|
|
|
|
|
|
|
Voltage
|
|
|
|
Set by internal plug: nominal 115V or 230V at 50 - 60Hz AC.
230V setting: Min 160V (restricted output power): Max 263V
115V setting: Min 80V (restricted output power): Max 132V
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Consumption
|
|
|
|
Quiscent: 55W. Typical use: 130W. Max: 415W.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Note
|
|
|
|
0dBv = 775mV into open circuit.
|
|
|
|
|
|
|
|
|