 |
Specification - VS3208
|
|
|
|
|
|
|
|
|
|
Size (WxHxD)
|
|
|
485mm x 612mm x 395mm
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Weight
|
|
|
47 kgs
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Drivers
|
|
|
Bass: 2 x 200 mm (8") cone driver
Mid: 1 x 75 mm (3" soft dome
HF: 1 x 28mm (1.125") soft dome tweeter
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Maximum SPL
|
|
|
117dB
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Frequency Response
|
|
|
42Hz - 20kHz +/-2dB
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Sensitivity
|
|
|
|
90.5dB at 1W at 1m
|
|
|
|
|
|
|
|
|
|
Input
|
|
|
|
|
|
|
|
|
|
Connector
|
|
|
|
XLR3 Female
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Impedance
|
|
|
|
10 kohm. Electronically balanced, RF filtered
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Wiring
|
|
|
|
Pin 1 Ground, Pin 2 Hot, Pin 3 Cold
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Sensitivity
|
|
|
|
Rear mounted 10 position rotary switch calibrated in 2dB steps.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Maximum
|
|
|
|
+4dBu for 100dB SPL at 1m: Max input level for clip >+16dBu at 5kHz
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Minimum
|
|
|
|
-14dBu for 100 dB SPL at 1m: Max. input level for clip >-2dBu at 5kHz
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
User LF EQ
|
|
|
|
3 position rear mounted switch to select: FLAT for normal use, CUT for nominal 2dB cut below 100Hz and LIFT for nominal 2dB LF lift below 80Hz
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
User MF EQ
|
|
|
|
3 position rear mounted switch to select FLAT for normal use, CUT for nominal 2dB cut and lift for nominal 2dB LF lift in the frequency band 500 - 3kHz
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
User HF EQ
|
|
|
|
3 position rear mounted switch to select FLAT for normal use, CUT for nominal 2dB cut and lift for nominal 2dB LF lift above 5kHz.
|
|
|
|
|
|
|
|
|
|
Power Amplifier
|
|
|
|
|
|
|
|
|
|
LF output power
|
|
|
|
230W rms continuous*
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Mid output power
|
|
|
|
110W rms continuous*
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
HF output power
|
|
|
|
100W rms continuous*
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
T.H.D.
|
|
|
|
<0.03% at levels up to 1dB below clip, 20Hz - 20kHz. typ 0.005% at 20W rms 1kHz
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Hum + Noise
|
|
|
|
> -100dB referred to clip
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
*Note: The continuous rating is for a period not exceeding 5 minutes with unrestricted airflow (100mm clearance) around the amplifier heatsinks and ambient temperatures is <30°C.
|
|
|
Indication
|
|
|
|
|
|
|
|
|
|
Power on
|
|
|
|
Front mounted LED (green) indicates power applied
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Overload
|
|
|
|
Front mounted LED (flashes red) indicates 0.5dB below signal clip
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Thermal protection
|
|
|
|
Front mounted LED turns red, signal is muted and amplifier switches to standby mode during thermal protection cooling cycle. Normal operation resumes when heatsink temperature drops by 20 C
|
|
|
|
|
|
|
|
|
|
Power requirements
|
|
|
|
|
|
|
|
|
|
Voltage
|
|
|
|
Set by internal plugs: nominal 115V or 230V at 50-60Hz AC.
230V setting: Min 160V (restricted output power): Max 263V
115V setting: Min 80V (restricted output power): Max 132V
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Consumption
|
|
|
|
Quiescent 105W, Typical use 280W, Max 950W
|
|
|
|
|
|
|
|
|